Description: Product highlights6-channel car amplifier 125 watts RMS x 6 at 4 ohms (200 watts RMS x 6 at 2 ohms) 400 watts RMS x 3 bridged at 4 ohms (4-ohm stable in bridged mode) Class D amp technology AccuBASS® circuitry for improved bass response MILC™ (Maximum Input Level Control) LED optimization and clip indicators stereo/mono switch on channel pairs Ch 1/2: variable high-pass filter (30-5,000 Hz, 12 dB/octave) Front High input level control — when using amplified factory tweeter wiring Ch 3/4: variable high-pass or bandpass filter (HP: 30-300 Hz; LP: 500-5000 Hz, 12 dB/octave) Ch 5/6: variable high-or low-pass filter (30-300 Hz, 12 dB/octave) 8 speaker-level inputs (summable) GTO™ (Great Turn On) signal-sensing turn-on with Ch1/2 speaker-level input preamp inputs and outputs optional wired remote level controller available fuse rating: 40A x 3 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier dimensions: 12"W x 2-1/8"H x 8-1/16"D warranty: 5 years What's in the boxAmplifier 2.5 mm Allen wrench Quick-start guide About this itemWritten by Crutchfield's Buck PomerantzPower galore Two keys to unlocking great sound in a car stereo system are serious power and extensive control — and this amp's got them both. For power, AudioControl's DM-6.1200 6-channel amplifier puts out 125 watts RMS per channel, so it'll drive even the most demanding aftermarket speakers with plenty of headroom to spare. And if you're into bass, you could bridge this amp to 3-channel mode to drive three subwoofers with 400 watts RMS each, 1200 watts in total. Active controls for active systems This amp will work well with a 3-way system that uses a pair of tweeters, midrange speakers, and subs. Highly adjustable crossover networks let you set high-pass, low-pass, and bandpass filters so each driver gets only the frequencies it was designed to play. AudioControl's AccuBASS® circuit ensures maximum bass performance, even if you're connected to a factory radio that normally turns down the lower frequencies as you turn the volume up Add kick to your factory stereo AudioControl designed the LC-6.1200 to work equally well with aftermarket and factory stereos. Eight active speaker-level inputs allow you to connect to almost any factory radio, with signal summing accommodating the separate bass, midrange, and treble signals found in some factory systems. Signal sensing circuitry turns the amp on, via the front speaker-level inputs, so you won't need to run a remote turn-on wire throughout your vehicle. Convenient features Onboard LEDs indicate optimized signal flow for inputs and outputs, plus give you a warning when a source is too loud and causing distortion. An optional wired remote can get assigned to each and every channel pair so you can control volume from the front seat. Important Note: Some factory radios and amplifiers will not work without sensing that its speakers are connected to their outputs. If you don't have output from your factory system after installing this amplifier, you'll need an AudioControl AC-LGD load-sensing adapter (sold separately) to correct the issue. LC-6.1200 connection panel
Price: 789 USD
Location: Charlottesville, Virginia
End Time: 2024-11-21T20:40:10.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Seller
All returns accepted: Returns Accepted
Item must be returned within: 60 Days
Refund will be given as: Money back or replacement (buyer's choice)
Return policy details:
UPC: 851523007201
Type: All Car Amplifiers
MPN: LC61200
Brand: AudioControl
RMS Power: 1200W
Channels: 6
California Prop 65 Warning: WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP) which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Model: LC-6.1200
