Curtain Hanging Track System (PVC) w/ Ball Carriers installed, PRICE IS PER FT!

Description: PLEASE NOTE: This listing is for ONE FOOT of rail at $9.00 per foot with ball carriers installed on industrial curtains or golf simulator curtains purchased from us. A quantity of 1 will only get you 1 foot of rail, not an entire 3'8" max-length of rail. Please enter the NUMBER OF FEET you want in the QUANTITY FIELD. Any orders of less than 8 feet of track will incur a shipping surcharge of $25.00. This surcharge will not be automatically deducted at the point of order, but will be requested separately prior to your order shipping out. To avoid this surcharge, please order a minimum quantity of 8 feet. This is a great economical Curtain Hanging Track System for straight curtain hanging or for twisting around corners. It can be steam-heated if necessary to bend at tighter angles. Easy to cut with a hacksaw. Drill holes every 12 inches through the center of the track, with at least one hole next to each end of the track. Screw down the track to secure, using the provided special flathead screws. You specify how many feet of rail you want in the Quantity field, and the railing will be provided with an initial Ball Carrier, plus an additional carrier per every foot of railing ordered. For instance, an order of 15 feet of rail will include 16 ball carriers. These ball carriers fit right into the groove of the rail and slide easily, allowing you to open and close your curtain(s) or move them off to the side. To attach the ball carriers to your curtain, sandwich the hemmed curtain fabric between the jaws on the carrier. Tighten the two included screws through the fabric and into the opposite side of the carrier. Place carriers every 12 inches along the top of your curtain, corner to corner. Need more Ball Carriers than your order would come with? You can order extra Ball Carriers from this listing: http://www.ebay.com/itm/152536520942 For the railing, you will be provided with one initial screw, plus an additional screw per foot ordered, plus an additional screw for each area where the track ends will join together. For instance, an order of 11 feet of rail (provided as three 3'8" pieces) will include 14 total screws (1 + 11 + 2 = 14). These are special flathead screws (4 x 6 x 3/4") requiring a square-head screwdriver, that will not inhibit the rail from working properly as they fit flush within the track. Using generic or other type screws will cause problems, and possibly block the ball carrier from moving freely within the track. Since there are no pre-drilled holes in the track, you will be required to drill holes through the track and into the surface you're mounting it to, prior to putting the screws in. The last picture above shows of a set of four of our Silver Economy Panels being hung using this curtain track system. Curtains not included. If you will be ordering this Track System simultaneously with one or more of our Stage Curtains, we will install the Ball Carriers onto the curtain(s) at no charge! - but we will omit the grommets and the webbing on the hem. Please note that the Ball Carriers fit best over the top hem without webbing, as the webbing makes it too thick. (Still possible if you already have our curtain with the webbing hem, but the clamps on the carriers will bow out slightly). After installation, the distance from the ceiling (or surface that the track is mounted to), to the top edge of the curtain, will be 1 inch. Instruction/installation manual not included. FREE SHIPPING to anywhere in the USA lower 48 states. Surcharge for Alaska, Hawaii, and Puerto Rico. International shipping cost based on location. Maximum shipping length (after packaged): 4 feet. The max rail length for any single piece is 3'8". Specifications:Curtain Hanging Track System with Ball Carriers and ScrewsTrack and carriers made from Extruded PVCColor: Black (rail and carriers)Rail Outside Measurements: 5/8" x 5/8"Rail Inside Width: 3/8"Ball Carrier Overall Length: 2.5"Ball Carrier Width: 0.628" Rail Specifications: A. 0.177" B. 0.465" (vertical) C. 0.395" (horizontal) D. 0.641" F. 0.577" Ball Carrier Specifications (Front): A. 2.510" B. 0.321" C. 0.342" D. 1.875" E. 0.628" Ball Carrier Specifications (Profile): F. 0.350" G. 0.785" (center-to-center) H. 0.275" I. 0.513"

Price: 9 USD

Location: Clinton, Massachusetts

End Time: 2024-08-28T20:59:46.000Z

Shipping Cost: 0 USD